Showing results: 196 - 210 of 273 items found.
-
Thermtest Instruments
Thermal conductivity is a measurement of a materials ability to conduct heat and can be critical for evaluating energy efficiency and thermal performance of materials. The HFM-100 Heat Flow Meter is designed as an easy-to-use method for the measurement of thermal conductivity and thermal resistance of insulation products, construction materials, packaging, and assemblies. Available at an exceptional value, the Thermtest HFM has been engineered for industry-leading performance by combining the highest accuracy, repeatability, and widest temperature range possible, and follows international standards: ASTM C518, ISO 8301, and EN 12667.
-
7A -
Picoprobe
An unterminated version, can be used for capacitance and resistance measurements or in low to medium speed signal applications where a 50 ohm termination is not required. A flexible coaxial cable length of 6 feet in length is standard on the Model 7A; however, when used for capacitance measurements, GGB Industries, Inc., recommends using a shorter 3 foot cable. If a shorter length of cable is desired for capacitance measurements, please specify it when ordering (Model 7A-3ft.). Please note that Model 7A uses Model 7 replacement tips.
-
TOS7210S -
Kikusui Electronics Corp.
The PID insulation tester (TOS7210S) is designed based on the insulation resistance tester (TOS7200) to carry out the evaluation of the PID (Potential Induced Degradation) effect of the PV module precisely and efficiently. Being equipped with the output ability of 2000 V and the ammeter with nA resolution as well as a polarity switching function, the TOS7210S is also applicable not only to the PID evaluation but also the evaluation of the insulators that requires a high sensitivity of measurement. The tester is equipped with the panel memory that is externally accessible and RS232C interface as standard; it can be flexibly compatible with the automated system.
-
KT3201 -
Ketai instrument (kunshan) Ltd.
KT3201 KT3202 KT3203 KT3204 four high-precision multimeters are specially designed for European student watches.It has AC and DC voltage, DC current, resistance, capacitance, continuity, and diode measurement functions.Comply with safety standard CAT III 600V Fuse Φ6x31mm 600VKT3202 is a specially designed AC and DC voltmeter.KT3203 is a specially designed AC and DC ammeter .KT3204 is a specially designed DC low-current, low-voltage meter. The voltage can be measured from 0 to 100mV, and the current can be measured from 0 to 50uA.The pointer "0" is at the median value, and the voltage and current are divided into two sides.This set of four tables has certain practical significance for students' knowledge and understanding of Ohm's law in electrical engineering.This set of meters complies with the CAT III 600V standard.
-
AMETEK Sensors, Test & Calibration
Temperature measurement and calibration is our specialty, allowing us to provide much more than just standard sensors and assemblies. Our long experience, developing and producing industrial temperature sensors, provides us with a wide knowledge about applications and customer needs. This enables us to build and deliver quick and custom-designed quality temperature sensors for almost any kind of solutions and applications, no matter what industry. We offer a complete range of thermocouple assemblies and resistance thermometers, as well as thermocouple wire, extension wire, temperature transmitters and accessories.
-
Gill AC -
ACM Instruments
ACM's flagship instrument offers a Potentiostat, Galvanostat and Zero Resistance Ammeter with integrated Frequency Response Analyser and Sweep Generator in one.Electrochemical tests such as AC Impedance (EIS) and standard DC tests including LPR and current and voltage noise are included, making this instrument extremely versatile and great value for money.To better meet your specific needs why not customise your instrument with our options, so versatile are our instruments that many options are even available to be fitted retrospectively, making our instruments the right choice now and for the long term.
-
NF-514 -
Shenzhen Noyafa Electronic CO.,LTD
*Cement Concrete Professional Thermometer.*Built-in LCD Lighting Function: Working in harsh environments, clear readings.*Exquisite material selection and lightweight design.*Built-in Temperature Measuring Line, Durable and High Temperature Resistance.*Embedded Line Asphalt Temperature Measurement.*Small size,light weight, easy to carry, suitable for construction sites and field operations.*Certification. Passes RoHS, FCC, and CE compliance testing, and Noyafa is certified to the ISO 9001 standard.*100% Affordable. Manufactured in China and a lot cheaper than competitor products with similar quality.
-
FSC Series -
Axiomtek Co., Ltd.
*Compliant with CFast™ 2.0 Standard, Capacity SLC: 2 GB ~ 64 GB, MLC: 4 GB ~ 128 GB*SATAIII interface*Suitable for high demanding applications*Well performed under harsh operating environment and industrial temperatures*Anti-vibration & shock resistance*Support static wear leveling algorithm*S.M.A.R.T. & i-S.M.A.R.T. Supported*Intelligent system for error recovery*Excellent data transfer speed*Extremely low power consumption*High operating reliability & durability*Hardware write protect*Enhanced power cycling management
-
SCR ELEKTRONIKS
GLOW WIRE TESTER (also known as Glow Wire Test Apparatus) is designed to carry out fire hazard testing as specified in IEC 60695-2-10 2000-10. Flammability test is to check the ‘Resistance to Fire’ of electrical insulators that touch directly conducting parts & also parts of insulators. This test is also referred in many other standards such as IS 11000, IS 3854 : 1997 / IS 1293 :1988 / IS 371 :1999 & IS 11000 Pt 2 Sec 1, IEC 60335, IEC 884/94, IEC 60598, IEC 61058, BS 6458, BS EN 60695–2-10,11,12, etc.
-
GWT A2 -
SCR ELEKTRONIKS
GLOW WIRE TESTER (also known as Glow Wire Test Apparatus) is designed to carry out fire hazard testing as specified in IEC 60695-2-10 2000-10. Flammability test is to check the ‘Resistance to Fire’ of electrical insulators that touch directly conducting parts & also parts of insulators. This test is also referred in many other standards such as IS 11000, IS 3854 : 1997 / IS 1293 :1988 / IS 371 :1999 & IS 11000 Pt 2 Sec 1, IEC 60335, IEC 884/94, IEC 60598, IEC 61058, BS 6458, BS EN 60695–2-10,11,12, etc.
-
AMIC-15k1 -
Amperis sl
*The partial discharge indicator PDI.*Diagnosis of insulation systems based on standard measurements of IR, DAR, PI, SV, RT, DD*Allows to test the electrical durability of the tested object - indication of breaking voltage.*The high resistance to electromagnetic interference ensures uninterrupted operation in power plants and near high-voltage transmission lines up to 1200 kV AC and 500 kV DC.
-
National Technical Systems
Gravelometer testing is designed to evaluate the resistance of vehicle surface coatings (paint, clear coats, metallic plating, etc.) to chipping caused by the impacts of gravel and other flying objects in accordance with SAE and ASTM standards. The primary usage of this test is to simulate the effects of the impact of gravel or other debris on automotive parts. Test samples are typically mounted in the back of the Gravelometer, and air pressure is used to project 1 pint (approximately 300 pieces) of gravel at the sample. The test sample is then removed and gently wiped off with a clean cloth. Tape is then applied to the entire tested surface. Removal of the tape then pulls off any loose fragments of the coating. The appearance of the tested sample is then compared to standard transparencies supplied by SAE to determine the chipping ratings. Visual examination can also be used to describe where in the coating/substrate system that the failure has been induced.
-
DWC-1 -
Lisun Electronics Inc.
This low-temperature impact device is compliance with standard requirement of IEC60245, IEC60227, IEC60540, GB5013-2008, GB5023-2008 and GBT2951-2008. It’s used to test all kinds of PVC sheathed cable, wire, soft wire and no sheath of parallel soft PVC insulated impact resistance at low temperature. Specification: • Working temperature: -15℃±1℃ • Impact height: 10~200mm adjustable • Length of specimen: 5D~150D • Material: 304 stainless steel • Completion time once: 3~5s • Completion number of units for once: ≥2pcs • Weight: 100/200/300/400/500/600/750/1000/1250/1500g • Low temperature box to match additionally
-
TFBS-6 -
Titan Tool Supply, Inc.
The new 17,000 element high resolution imaging bundle offers superior image quality. They feature an objective end tip that can be deflected 120 in either 2-way or 4-way articulation by using a control knob next to the eyepiece housing. This enables easier positioning around elbows and bends in the work piece, while enhancing the viewing area. The new Tungsten braid sheathing offers superior protection and abrasive resistance than standard sheathing. The TFBS-6 Series eyepiece now has a direct photo adaptable C mount, to connect directly to an industrial video camera, no need for an additional video coupler.
-
Ferrites India
Flux meter has been the established standard for the measurement of magnetic flux density for determining total flux in a magnet or magnetic assembly. Its use was curtailed except in a few specialized areas because of many factors such as the difficulty in setting up light beam flux meter or ballistic galvanometers, limitations on the ohmic resistance of search coils, the requirement of some degree of operator skill in reading the flux meter etc. The development of the integrating type Digital Flux meter has virtually cancelled the hitherto negative aspects of fluxmeterology and has found a broad niche for many magnetic measurement applications.
